An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters . SN74LS (ACTIVE) Octal Buffers And Line Drivers With 3-State Outputs. Datasheet ( KB). Diagram click to expand contents. Functional Diagram. Octal 3-state Buffer/line Driver/line Receiver. These buffers/line drivers are designed to improve both the performance and PC board density of 3-STATE .
|Published (Last):||13 October 2012|
|PDF File Size:||8.7 Mb|
|ePub File Size:||18.91 Mb|
|Price:||Free* [*Free Regsitration Required]|
So I’ve searched for days for information about the 74HC line driver. As always, the Datasheet provides raw and not very good information about the actual component: I mean, it gives us the temperatures, but not datashet the actual component works Any way, there is very little information about Line Drivers in general.
So, how do thy actually works? And how the can act as a line driver?
All I see in the inner structure is enables and input to outpuut wires. I think that in order to reduce the current that the FPGA suplies to the servo, I need to put the in between them, thus reducing the “effort” from the Altera. Or the Altera can provide a good current flow to the servo without damaging it’s abilities? A line driver is simply a buffer.
What you put in one end comes out the other. The increased current is able to overcome the capacitance caused by having many devices on a bus.
74244 Datasheet PDF
I’m not sure what you mean by “how it works”. The datasheet tells you pretty much everything you need to actually use the part, though NXP does tend to be a bit sparse on internal details. Anyways, if you look around a bit, you can find some slightly datashset datasheets that have more detailed internal diagrams.
The datasheet also states: If you want more detail, you should start reading about how transistors work, and how they’re used to make the logic gates in the shown diagram.
The datashwet is to provide a power gain. The circuits that are driving the inputs may not have the power to drive the impedance of a longer wire length. This chip does not perform any logical function; it is just giving the signal a strength boost. The line driver 774244 serves to isolate the local circuits from electrostatic discharge from connections that might go off the board. The second functionality is that it has a tristate output, which means that when the enable pin is not asserted the chip does not drive the output signal datahseet all.
It’s as if the chip were datashert from the wire. This allows you to have multiple line drivers on the same wire, and as long as they properly take turns driving it they can share the single connection. Tristate mode also saves power by not driving the line when there is nothing to send. It should be noted that the device identified above is a “tri-state” driver.
DATA SHEETS SN74xx, SNxx, SNxx, SNxx, SNxx, SNxx
This means that it can set the line “high”, “low”, or can effectively disconnect itself from the line. This is used in situations where any of several components 7444 “drive” the bus though hopefully not more than one at a time. It can be used, eg, for a “bi-directional” bus between processor datasgeet memory or between processor and devices: The enable function is datsaheet to all four drivers and offers the choice of an active-high or active-low enable G, G input.
Octal 3-STATE Buffer/Line Driver/Line Receiver
Home Questions Tags Users Unanswered. How does a Line Driver actually works? Eminem 1 3 8. That datasheet gives everything you need to actually use a 74HC It sounds like you’re looking for a equivalent circuit.
In case it’s the apparent lack of power to the chip that’s confusing you: The functional diagram on that datasheet omits the power pins, but they are there and must be powered for the part to function. That power is used by each buffer element to increase the load it can drive. You can think of it as the logic gate equivalent of an amplifier.
But how it works? I mean, how the can increase the current with just sending the input to the output? Eminem – What makes you think the input is connected directly to the output? What do you think a buffer is? Eminem Language barrier here, I think.
There are two principal functions of this line driver. Jeff Bell 1 4. Hot Licks 3 8. How does a line driver actually work? Sign up or log in Sign up using Google.
Sign up using Facebook.